Lrl from Italy

[FrancoItaly]

Greetings to all,
I want to add also that the people who are sensitive to this phenomenon are very sensitive to millivolts, even if they are in a capacitor... like 100uf16v.... I have seen it. Those abilities can go from father to son and to grandson. Personally, I don't have it but my cousin and his father my uncle. Finally I want to congratulate you all for your time to write to this post and especially to Mr Franco for his contribution to sharing a knowledge to all as global society we must be

.

Several people have above-average sensitivities, I myself practice pranotherapy (for family and friends) and a friend of mine as well as practicing remote pranotherapy as well as always making diagnoses at a distance, even many kilometers away.

[folharin]

I post the Dream_Man pcb for a member.

give up on this project!!

[omar]

Welcome . They say in general metals reflect the electromagnetic beam and begin to resonate at the harmonic frequency only. For example, if a plate of gold is placed between two sheets of copper at the signal entrance of a highly sensitive electronic receiver, the plate of gold will prevent the signals from passing through and reflect them. In contrast, it will absorb and pass the harmonic signal. What do you think of this filter? I think the signal is treated like high frequencies, microwaves, similar in small capacitance. with a low pulse. Is there a comment.

[FrancoItaly]

Welcome . They say in general metals reflect the electromagnetic beam and begin to resonate at the harmonic frequency only. For example, if a plate of gold is placed between two sheets of copper at the signal entrance of a highly sensitive electronic receiver, the plate of gold will prevent the signals from passing through and reflect them. In contrast, it will absorb and pass the harmonic signal. What do you think of this filter? I think the signal is treated like high frequencies, microwaves, similar in small capacitance. with a low pulse. Is there a comment.

All theories must explain the fact that buried metal only generates the phenomenon after months or years.

[omar]

There are no theories. My idea is to use gold to detect gold based on the nuclear magnetic response of the metal atoms on the basis of resonance harmonics. in the field of land. We lack finding ways to apply and make sure of work and feasibility. When the gold sample enters a resonant field (buried gold), energy exchange will occur for the atoms of the gold sample, and a weak magnetic oscillatory signal will be given as a reaction. It can be detected with an electric circuit. Thank you

[omar]

All theories must explain the fact that buried metal only generates the phenomenon after months or years.

I saw a camera that works on the principle of phenomenon, depicting a dry water well. Water was pumped from a truck into the well, and for a moment water began to appear filling the void, the color of the water was black. This indicates that the phenomenon appears quickly, but it takes time to become more intense on the surface.

[FrancoItaly]

I saw a camera that works on the principle of phenomenon, depicting a dry water well. Water was pumped from a truck into the well, and for a moment water began to appear filling the void, the color of the water was black. This indicates that the phenomenon appears quickly, but it takes time to become more intense on the surface.

If the camera is sensitive to infrared it is possible that it only senses the temperature difference between the void and the water, I'm not sure if this is the phenomenon.

[perzo]

Hi everyone. When I put my hand close to the Franko antenna, the LED turns off. Where is the problem? Thanks.

[FrancoItaly]

Hi everyone. When I put my hand close to the Franko antenna, the LED turns off. Where is the problem? Thanks.

No problem, in fact one of the tests I suggest is to check if touching the antenna decreases the signal. This tells us that the sensor stage is working properly.

[Zicos]

hi mr franco.i'm new to the forum.and completely new to electronics.but i managed and made your 8mhz sensor.in the first one i made i used bc547c and c9,c13,c14(680pf)and c2(4?2.2pf)in series .the output voltage is 5.35v with 8mhz crystal . when I touch the 5.34v antenna, there is a voltage drop, that is, the sensor is working correctly. inside the house, it does not react to electronic devices. it only picks up the mobile phone call, and that too from very close. outside in the garden, it picks up a very good signal from a distance of 2 meters but from south to north and 0.50 cm from north to south. from the other directions it does not catch anything. I have seen the spot with a metal detector and I believe it is a copper alloy coin from my experience. I do not dig it to have it as tests. but in my field where I have an old copper pot buried for 5 months, it doesn't catch it. I don't have gold and silver yet to put it in. at night it works with only one LED while during the day all three light up. it is believed that it doesn't tune in my area??????what do you recommend me to do????the copper board is double sided with top side bonding, I have the sensor in Faraday shield and the whole box also with ground and aluminum foil the handle is 30 cm from my hand. I am from Greece. and one more thing I would like to ask you and anyone else who knows about the silver loop, how is it made with the wire dimensions, loop diameter? greetings to all forum members and thanks to the admins for accepting me....

[FrancoItaly]

I think the sensitivity of the sensor stage is insufficient. In the calibration did you obtain self oscillation with the quartz oscillator disconnected? I attach the helps and add, perhaps it wasn't understood in the helps) that at the beginning you have to obtain the self oscillation and therefore you have to decrease the gain (via C13 and C14) until it disappears.
The maximum sensitivity in our hemisphere is in the north/south direction and the minimum is south/north.

[Zicos]

hello Mr. Franco, thanks for the quick reply. without crystal the voltage is zero volts. as soon as I connect the antenna the voltage is 1.90 volts with a 97cm antenna and a 25cm antenna connection cable. when I put another antenna the voltage is different again. how do I calibrate for 0 volts without quartz? with antenna or not?, and if with antenna the length of the antenna? sorry for so many questions, thank you for your help, be well.

[Zicos]

good morning Mr. Franco, I did a calibration with a 97cm antenna and a 25cm connection cable, I now put c13(220pf) and c14(100pf) and c9(450pf) and the output voltage is 0 volts without crystal and the voltage with crystal is 5.04 volts. without crystal and with 20cm antenna closed the voltage is 1.50v, as soon as the antenna is open the voltage drops to 0v .what is the problem? is c9 critical in this problem?

[FrancoItaly]

During calibration, in the laboratory, I put a 30cm piece of wire connected to L1 as an antenna, to connect the stylus antenna with L1 I use a cable of about 10cm and I usually extend the antenna 30/40cm. The longer the antenna, the greater the sensitivity, but 1m seems excessive to me.

[Zicos]

thank you very much for helping me. when the calibration is done with the 30-40 cm antenna open and you have 0 volts, then close the antenna is the voltage still 0 volts? or do you have volts?