Antiphase spiral coil transmitter + receiver

[Mike(Mont)]

Proticty and dowsing are intertwined. You use the dowsing or Supersensonics to study the proticity. Hills was not being very Politically Correct when he said something like: Second hand knowledge on the subject is like reason to a mindless fool.

[enjoykin4]

Yes I agree with you Mike(Mont).

Power source of "Proticty" is a Human mind (not biological structure knwn as a Brain".
Our thoughts are flows of Proticity.

Mind is multidimensional energetic structure.

DNA and RNA spirals are also multidimensional energetic structure and all these structures also our bodies were made in unique Naturaly proportion - Golden proportion of fi and 1/fi. fi=1,6180339887498948482045868343656......

[Mike(Mont)]

Yeah, well don't confuse it with the psychic stuff. Here's an example: Say you have a forked stick and you found an underground water source. Now you walk away from the spot until you get another rod response. This distance is equal to the depth of the water. Now if you were going to do it psychically, you would just stand there and count the number of feet (or meters) until you get a response. There is a big difference here in accuracy.

[WM6]

Construction of spiral log antenna

Here one possible practical construction of Spiral logarithmic antenna.
I am taking hard paper for antenna body.
It can be out of hard foil, conical plastic tube, polystyrene or wood too.

My dimensions are to suit to RX antenna EM shielding container.
There can be other dimensions too.
More pictorial:

[Mike(Mont)]

WM6, thanks for the info. Is each set of turns connected to the next in series?

[WM6]

Yes turns sets are serial connected - this way:

[Mike(Mont)]

Okay, Thanks WM6. Looks good.

[WM6]

Such yarn cones from yarn mill in textile manufacturing could be very practical body for spiral conical antenna:

[Mike(Mont)]

WM6, thanks. You gave me some good ideas to work on. Basically I need something flatter and inverse for a transmitter coil that has a wider pattern. I have my doubts this will work with the lower frequencies but i plan to jump in the deep water and see if I can swim.

[iron1944]

WM6
Grand Masters.
This has to be done in the same box assembly TX and RX?
Or held on the separation assembly?
thank you.

[WM6]

This has to be done in the same box assembly TX and RX?
Or held on the separation assembly?

Hi iron1944

It is almost impossible to zero-tune device if TX and RX are in the same housing.

RX part should be magnetically shielded too - not RF shielded only.

Conserve (dog) can is very cheap and effective shield for such purposes.

So, RX part inclusive RX antenna should be canned this way:



Whole device should be constructed this way:

[Mike(Mont)]

I'd tell everyone to put out your B.S. deflectors on this one. Those coils are pretty close to what is called a phased array. That's for microwave frequencies, not going to work for treasure hunting in the ground. Like I said in a previous post, this does not appear to be scalar wave generator. And the biggest tell is the guy won't even build one himself. What is that about? No confidence in his own hand. This looks right along the same lines as that calculator hoax. Maybe even the same guy.

[WM6]

You should not mix electromagnetic radiation with radiation structure for a (quasi static) vector and scalar signal potential. Last one radiated at common axis (zeroing plane) of capacitive and inductive vectorial planes which are opposite to each other.

Transmitter schematic is OK and can be used as anti-phase current (for inductive component of antenna) and voltage (for capacitive component of coil) source.

First proposed antennas (as I previous say) was not intended for scalar wave generation, cause inductive and capacitive components are not separated enough in such array to be tuned for zeroing independently. So for scalar wave generating TX antenna radiator should be reconstructed and simplified. But proposed anti-phase electronic circuit is proper, simple, reliable and effective.

Basic scalar wave generation radiator (TX scalar antenna) should look like this:




Tuning (zeroing) here mean to tune at maximal suppressed (nulled) electromagnetic field
in horizontal (forward) plane of this vector scalar radiator. This at the same time mean
achieving maximum at scalar and vector potential at the same horizontal plane.

Transmitter circuit can be incorporated (including battery) in middle radiator tube.