BIOnic 01 Schematic

[WM6]

What are 741, BP109, P1-3?

741 - probably most known linear amplifier in the world, BP109 - phototransistor- can be replaced, ask your electronic parts dealer, P1-3 = pots (is this your first schematic?)

How can I adjust this detector?

Described in topic.

Is vacuum in the tubes?

If you need ionisation chamber then you use clean kerosene (petrol) or much better isooctane (C8H1) , cause vacuum cannot be ionised.

what is under the contact lenses?

read previous answer

Can I detect hidden gold below the earth?

Only if you are born dowser, otherwise, better to use metal detector.

!_!

[gps]

!_!

Dear WM6,

thank you very much. Yes it is my first schematic.

best regards

[expert]

hi every body itry to do this schematic but it didnt work
is this bcz
1-wrong schematic
2-distance betwen tube and laser
3- using(red laser pointer) not using infra red
4-or we are too slow to see the effect so we need digital signal proccing high speed

thanks alot

[WM6]

1-wrong schematic
2-distance betwen tube and laser
3- using(red laser pointer) not using infra red
4-or we are too slow to see the effect so we need digital signal proccing high speed

5- you are not born dowser, as you have to be, to successfully work with such devices.


Dowsing tool in dowser hands, no matter if it is out of wood or full of modern electronic, it is olways only utility means to an end approach of your inner dowsing capability.

Mean, there are not outer way to successfull dowsing (such as self-operating PD device), there are only inner way and different dowsing utilities as PD's are only tools to help your inner concentration on matter.

PD's cannot find nothing by itself.

[expert]

good feed back but???

hallo every body i work from three days on this schamtic for bionic
it give me agood result but in sun shine in the night it doesnt work why what is the reason
is their asolution

thanks alot

[WM6]

Probably laser is to weak or sensor tube receive in wrong direction regarding reflected beam try and tune directivity first from vicinity 1 to 2 m.

[Morgan]

BIONIC 01

hallo every body i work from three days on this schamtic for bionic
it give me agood result but in sun shine in the night it doesnt work why what is the reason
is their asolution

thanks alot

Hello


In other thread you said cant put the BIONIC to work becouse something is wrong with schematic.
What corrections did you find in schematic?
What you found with this BIONIC,and distance?


Regards

[expert]

itry this

ok i do the schematic exactly
but i use resistor 200 ohm on the rgb led and i use lenses (glass one) with 3.75 correction
on gold rgb led well be off in sun shine only(you must Caliber very well)
thats all

[expert]

thank you wm6

thank you wm6 i well try to but another laser pointer is the green one stable to work thanks

[WM6]

thank you wm6 i well try to but another laser pointer is the green one stable to work thanks

Green laser is one the best (of course it depend on how much mW we get out of it). There can be problem with directivity of sensor tube. Sensor have to be positioned in direction of reflected laser beam. Another problem is, if laser light wavelengt (color of laser light) does not correspond to fototransistor dedicated wavelenght (color light). Those two dedicated wavelenght have to correspond to each other.

[expert]

ineed help again

hallo wm6 itry a good laser pointer and agreen laser also and the sensor included the wave length which i use in laser but in night it doesnt work again what is proceduer to fix that

thanks

[WM6]

hallo wm6 itry a good laser pointer and agreen laser also and the sensor included the wave length which i use in laser but in night it doesnt work again what is proceduer to fix that

thanks

Try reflection from lower distance, say 1-2m first, and tune directivity of sensor. Directivity can be very delicate.

[expert]

hallo wm6 and thanks alot

hallo wm6 can you give me the destance between tubes and laser pointer and Diameter for the tube -if this be deffrent- and if i use 20 mw laser grean or red it is good or its not enough

thanks alot

[expert]

please wm6

please ineed answer thanks alot

[WM6]

hallo wm6 can you give me the destance between tubes and laser pointer and Diameter for the tube -if this be deffrent- and if i use 20 mw laser grean or red it is good or its not enough

thanks alot

Hi expert,

distance isn't so much important, you can take distance given in schematic and description. More important is focusing, tube and laser have to to be set at the same focus point. So you need first to decide at which distance you wish to dowse most of the time. Say that your selected distance is 3m, then you need to focus your sensing tubes and laser at the same focusing point at 3m distance. Request some precise work with fixed laser ON and small movement of sensor tubing to get LED response. Once you get LED response you need to fix tube too. Try for test first from smaller distance, say 1m and after skilled this, go on your selected longer distance.