Real signal generator for dowsing

[fmnotes]

If you have gap between rings 0,03mm, you can use PCB. My opinion is... more difficult use PCB for this antenna
regards

I think if it works correctly and pcb copper, which will be easy for me to carve.
Otherwise need CNC MACHINE.

A question even if you use a signal amplifier, the amplifier output will not be better connects a coil around 8 ohms?
Performs better for the amp.

Thank you well.

[ANDREAS]

........A question even if you use a signal amplifier, the amplifier output will not be better connects a coil around 8 ohms?.........

You are right. For me at the moment, at interest only as an experimental model. About load 8 ohms is irrelevant, because the "technical load" is a resistance near the 50 ohm
best regards

[fmnotes]

You are right. For me at the moment, at interest only as an experimental model. About load 8 ohms is irrelevant, because the "technical load" is a resistance near the 50 ohm
best regards

Thank you ANDREA

[Dedevil]

Sorry to complain

I think this is a good project, but argue that everyone has jumped aboard and grown antenna out of their head in search of E.T. The basics of dowsing or divining by rod have been discussed on this forum before and I believe it was agreed by all that it is charge related. If we wish to take it any further, then let’s all go forward with science. And not go chasing Extra Terrestrials with fancy gadgets that have L.C.D. displays.

And so I will start a new thread,

Part 1 – Science of L rod dowsing

rgds

[fmnotes]

I think this is a good project, but argue that everyone has jumped aboard and grown antenna out of their head in search of E.T. The basics of dowsing or divining by rod have been discussed on this forum before and I believe it was agreed by all that it is charge related. If we wish to take it any further, then let’s all go forward with science. And not go chasing Extra Terrestrials with fancy gadgets that have L.C.D. displays.

And so I will start a new thread,

Part 1 – Science of L rod dowsing

rgds

What concerns many people is how to convey (the low frequencies to the ground) without loss of power.

[Dedevil]

Maybe some help

What concerns many people is how to convey (the low frequencies to the ground) without loss of power.

You could pick a deeper ground. Notice that Marconi's circuit has a earth in the ocean.

[fmnotes]

You could pick a deeper ground. Notice that Marconi's circuit has a earth in the ocean.

did not understand the answer, you explain that to me.

[antonis]

ac current is a f....d up current it uses possitive and negative it is slow for dowsing rod need big ampl..work
nice work andreas

[Nicolas]

Hi all

You can use it to build one real generator and simple

http://www.electronics-lab.com/projects/test/013/Schematic.png

I put here the Hex file

http://www.electronics-lab.com/projects/test/013/index.html

[goldfinder]

Get Sig gen off ebay

A similar signal generator is available on eBay for less than you can build one.
Goldfinder

[Mike(Mont)]

Generator work with flat-top aerial used in the VLF, LF, MF and shortwave bands. This antenna invented before 1920. The flat-top antenna functions as a monopole antenna with capacitive load.
The original flat-top antenna consists of a horizontal wires a vertical wire is connected to the center of the horizontal wire and hangs down close to the ground. Sometimes use many parallel horizontal wires, connected together at the center wire.
Here we can use this type antenna, with small mods for send signal in ground.
What we are newest?.
Replacing wires with a stable horizontal metal plate, building a certain way, so we have real capacitive load.
The antenna performance is close to 5%, depends on the accuracy of the construction. Usually amateur with handmade can produce perfomance 3-4% Not bad, if you understand, that simply needles the earth has performance near 0,5%. In this case you have performance up 400%
Materials for antenna
Your generator
two metal plates diametre 20-25cm.
IMPORTANCE only two plates have exactly the same dimensions.
coaxial cable connectors
A small plate diameter 1/10 of the large plate
Several personal work
See the schematic construction. I think is simple enough for everyone
I wish you success in all experiments in dowsing
best regards

This stuff is interesting, Just curious if anyone can interpret this diagram (post 8 of this thread) so an idiot can understand it. It shows the coaxial what appears to be two wires both attached to the lower plate--one to the lower surface and one to the center of the edge. It doesn't show any connection to the upper plate. Thanks. I assume the center wire of the coaxial is supposed to be attached to the upper plate and the shield to the lower plate.

[Mike(Mont)]

After a bit of head scratching I see the top plate is not connected and is supposed to reflect the energy downward. That doesn't look right to me, but pretty sure most people would say the same about me.

If you go to post 25 (by J_Player) down at the bottom of the post and read the second article on Tesla, this is what Konstantine Meyl is doing. He wrote his papers on this in 1990 but he used pancake coils instead of the long tube coil. Then at the bottom of that article are more links about capacitive antennas. I've mentioned this that the skeptics are misapplying theory when they argue against the frequency discriminators. Beaty discusses this, although not the discriminators.

[Mike(Mont)]

Well, what do I know? Meyl says that if you don't know what you are doing, this energy can be dangerous to humans so you might want to keep that in mind and read all you can about it FIRST. From all accounts, Tesla was not right in the head. I guess it didn't kill him but no one knows what it did to him genetically. it appears he neutered himself. Guess you can't say he was "nuts".

[Mike(Mont)]

BTW, this is hardly considered dowsing. It just shows most people not not even understand what the word means. J_player posted the links to Bill Beaty's explanation of Tesla's work and that I agree with. Geez, did i just say that? Oh, well. I've leave this alone because I really don't care what others think, but something is not right.

Well, maybe I take that back. If it is not sending a signal then I guess it IS dowsing.

[WM6]

To improve wave propagation, directivity and sensing, you can always combine capacitive and inductive elements: