Mineralisation, el.field electromagnetic field problems

[Avanturis]

Hello everyone
I want to open a subject (maybe it's already been discussed) that's been troubleing some members and that's a subject about mineralisation, el.field, electromagnetic field. I made many dowsing rods with signal generator, and i always have a a problem with mineralisation elektromagnetic fields. Can someone make a suggestion or a solution to fix this. (Or is someone keeping that for themselves)

[Brahimolayt]

Hi my friends.sorry I don't practice dowsing but false electromagnetic interference and fort miniralisation is a problem for me to. Even radiology transmitters, engine sparks, fluorescent bulbs,high wire voltage and transformers ....ets make my device gives fals bips. I think its do to the Lc tank tuning of the receiver circuit or the external oscillator the question is in what frequency we must tune to.and dowsing rods is the same to.

[Mike(Mont)]

Your area might be problematic but you didn?t say your location. GDI-Detectors.com has a relatively inexpensive device Eliminator e120. You can use it as a signal generator then set it to filter mode to check target size. Just set the filter and circle the transmitter again to see if the target line is still there.

[Avanturis]

Thanks Brahimolayt for your explanation

[Avanturis]

Your area might be problematic but you didn?t say your location. GDI-Detectors.com has a relatively inexpensive device Eliminator e120. You can use it as a signal generator then set it to filter mode to check target size. Just set the filter and circle the transmitter again to see if the target line is still there.

Hello Mike
Thanks for for answer,but do you have experience with the Eliminator e 120, or signal generator with chip ICL8038.
I know the chip ICL 8038 not manufactured but its sold on Ebay ,Amazon AliExpress.

[Avanturis]

Your area might be problematic but you didn?t say your location. GDI-Detectors.com has a relatively inexpensive device Eliminator e120. You can use it as a signal generator then set it to filter mode to check target size. Just set the filter and circle the transmitter again to see if the target line is still there.

Thanks Brahimolayt for your explanation

[Mike(Mont)]

Hello Mike
Thanks for for answer,but do you have experience with the Eliminator e 120, or signal generator with chip ICL8038.
I know the chip ICL 8038 not manufactured but its sold on Ebay ,Amazon AliExpress.

Is this a history exam? The 555 timer more current. 8038 not very stable

[Avanturis]

Is this a history exam? The 555 timer more current. 8038 not very stable

Thanks for your reply
I have no knowledge of electronics and I want to research and learn from some who have many years of experience so I ask here on the forum to find out more about generators

[Mike(Mont)]

There are many electronics courses on-line. I understand you don?t want my advice so hope you get it figure out.

[Mike(Mont)]

Pretty good chance you are doing something wrong if you getting so many false signals.

Aim the rods down 15 degrees?that?s like about two inches down from level. Another one is lock time?how long the rods stay crossed when you stand on the target line.

Turn the power down

[Avanturis]

There are many electronics courses on-line. I understand you don?t want my advice so hope you get it figure out.

Mike, your advice is good

[Avanturis]

Pretty good chance you are doing something wrong if you getting so many false signals.

Aim the rods down 15 degrees?that?s like about two inches down from level. Another one is lock time?how long the rods stay crossed when you stand on the target line.

Turn the power down

You have a lot of experience and therefore I will accept any of your advice to learn.

[Mike(Mont)]

If your area is magnetic volcanic lava with flour gold I don?t know the answer, have no experience

But I do know using l-rods is the weak link in the chain. People don’t seem to realize you must keep your conscious mind out of way. Easier said than done. I pick an object out in front of me a ways and just look at it—even examine it—while using the rods. This is to distract your mind from trying to control things

[Avanturis]

Let me tell you how I reject electrostatic fields.
I throw some electrostatic or electromagnetic fields with a copper rod stuck in the ground and hold it with one hand and I have lrl in the other, but some are so strong that I have to dig the place to remove the ions, electron, protons from the earth or whatever.

[Mike(Mont)]

No locator works perfectly all the time. Yesterday afternoon I tried the e120 and the signal was very weak to non-existent. I do not have the l-rods amplifier

I went out in the yard just now and it was biting my test target. Solar activity was up yesterday but my experience is Summer sun
can be overpowering during daytime

My test target just a fresh drop on the surface

Low battery 7.3 volts