My TOTeM project

[kahyal]

hi nicolas and other freinds
I've looked pcb.pcb is correct.The problem is related to printing pcb.You have prepared in the traditional way

it's for all friends...

[Nicolas]

hi nicolas and other freinds
I've looked pcb.pcb is correct.The problem is related to printing pcb.You have prepared in the traditional way

Thanks dear

This method of printing is professional my friend not traditional
I work not manual
I am a professional and I am a seller too.
my prototypes are without varnish without epoxy without silkscreen without enameling
but the other yes.

[roccocoin]

rx diameter ?

The TX coil has 75 turns of 0.56mm enameled wire on an 80mm diameter former. The resonant frequency is not that critical as the TX is a forced oscillator running at around 65kHz.
The RX coil has 100 turns of 0.56mm enameled wire.

Without the coils connected, you can test the power supplies are correct, and that the TX oscillator is working. If you connect the RX coil, it will be possible to use the device in passive mode, as there is no need to balance the coils. Balancing will be required after you add the TX coil.

still a pleasure, I wanted to know the diameter of the coil rx? 100 tourn 0.56 thread, but the diameter? tank
please give me this information because I can not find it and I did not pre-read the book, then I will buy sicuramente.tank and good evening

[Qiaozhi]

still a pleasure, I wanted to know the diameter of the coil rx? 100 tourn 0.56 thread, but the diameter? tank
please give me this information because I can not find it and I did not pre-read the book, then I will buy sicuramente.tank and good evening

The RX coil is wound on a ferrite rod.
See Chapter 14 of ITMD.

[roccocoin]

rx diameter

The TX coil has 75 turns of 0.56mm enameled wire on an 80mm diameter former. The resonant frequency is not that critical as the TX is a forced oscillator running at around 65kHz.
The RX coil has 100 turns of 0.56mm enameled wire.

Without the coils connected, you can test the power supplies are correct, and that the TX oscillator is working. If you connect the RX coil, it will be possible to use the device in passive mode, as there is no need to balance the coils. Balancing will be required after you add the TX coil.

hello, but you rx 100 tourn but the diameter and how? how many and great the rx 100 tourn? and not explained that diameter and rx can please tell me how and the diameter of the coil rx? tank

[roccocoin]

tx e rx .....ok?

hello, but you rx 100 tourn but the diameter and how? how many and great the rx 100 tourn? and not explained that diameter and rx can please tell me how and the diameter of the coil rx? tank

and right mounting for tx and rx? correct ?tanks

[roccocoin]

TX RX

and right mounting for tx and rx? correct ?tanks

La bobina TX dispone di 75 giri di 0,56 millimetri filo smaltato su un diametro di 80 millimetri ex. La frequenza di risonanza non è critica come il TX è un oscillatore forzato esecuzione a circa 65kHz.
La bobina RX dispone di 100 spire di 0,56 millimetri filo smaltato.

Senza le bobine collegate, è possibile verificare gli alimentatori sono corrette, e che l'oscillatore TX sta lavorando. Se si collega la bobina RX, sarà possibile usare il dispositivo in modalità passiva, in quanto non vi è alcuna necessità di equilibrare le bobine. Bilanciamento sarà richiesto dopo aver aggiunto la bobina TX.

P.S.You can figure out what and where the TX and RX and the? you have made a big mess that you can not figure out what and where the coil and the coil TX and RX, please, a little respect for those who are not so handy with electronics ...... the RX AND ROLL WITH FERRITE AND 75 OF THE SPIRE? THE TX AND EXTERNAL COIL WITH SPIRE 100? TANKS

[Qiaozhi]

Roccocoin - If you want to make a post in your own language, then please also provide an English translation.
Please read the forum rules -> Basic Rules of the Forums

In particular, this part: "Although this forum is open to everyone everywhere, I ask that posts be written in English to maximize participation. If English is not your native language, just do the best you can."

[roccocoin]

excuse me

La bobina TX dispone di 75 giri di 0,56 millimetri filo smaltato su un diametro di 80 millimetri ex. La frequenza di risonanza non è critica come il TX è un oscillatore forzato esecuzione a circa 65kHz.
La bobina RX dispone di 100 spire di 0,56 millimetri filo smaltato.

Senza le bobine collegate, è possibile verificare gli alimentatori sono corrette, e che l'oscillatore TX sta lavorando. Se si collega la bobina RX, sarà possibile usare il dispositivo in modalità passiva, in quanto non vi è alcuna necessità di equilibrare le bobine. Bilanciamento sarà richiesto dopo aver aggiunto la bobina TX.

P.S.You can figure out what and where the TX and RX and the? you have made a big mess that you can not figure out what and where the coil and the coil TX and RX, please, a little respect for those who are not so handy with electronics ...... the RX AND ROLL WITH FERRITE AND 75 OF THE SPIRE? THE TX AND EXTERNAL COIL WITH SPIRE 100? TANKS

Excuse me immensely, I had translated for me and then I did copy and paste directly. ancora.ma excuse me could you tell me where the coil and the tx and rx? that rx and the ferrite the baby? tanks

[Morgan]

TREASURE HOARD

Roccocoin - If you want to make a post in your own language, then please also provide an English translation.
Please read the forum rules -> Basic Rules of the Forums

In particular, this part: "Although this forum is open to everyone everywhere, I ask that posts be written in English to maximize participation. If English is not your native language, just do the best you can."

Hello

I decide to put here the news of a GREAT TREASURE OF GOLD COINS found recently in Greece with the PDK-2.3 model, this is not propaganda for sale PDKs, its the amazing find of a ceramic pot with a hoard of gold coins.
I stay silent about WHO FOUND the hoard, but it is cientific evidence that the gold inside sealed ceramic pot also irradiate the PHENOMENON.
About DISTANCE and DEPTH i dont know yet,this is today amazing news.
It willbe great if the person who foud the pot,give a gold coin as a souvenir

Regards all

[mustefa ubram]

hi to all
I would like to start construction.This is my box

[Goldmaxx]

hi to all
I would like to start construction.This is my box

Hello mustefa ubram,

Congratulations, looks very good. I 'm very curious about your experience with your Totem project.

Best Regards
Goldmaxx

[mustefa ubram]

hi Qiaozhi , goldmax ,morgan
Please help to adjust and calibrate totem?

[adamas1]

Is correct when approaching my hand at TOTEM was whistling

[rtl_2014]

HELP !!!!

dear friends.
after 2 week working on my totem pd i can test it on passive mode.
it work good with electromagnetic filed and ionic radiation devices.
at last test ( attached video) near the ferrite loop it can sense my watch tick tick and beep for each second changed.

http://youtu.be/Sdyxsla7lJc

but on active mode when i release the active/passive Switch to active mode red and yellow LED and the meter and buzzer turned to ON and by changing the active pot nothing happens
i changed position of ferrite and test it on each position please help me to calibrate may totem pd.
tanks

beast regards.