need mfd

[goldfinder]

Dell is at it again - covering up his fake LRL system

J PLAYER, you are so full of BS, you couldn't tell the truth if your life depended on it.

Shame on you for posting false information to unsuspecting viewers. Dell

I'VE SEEN Dell Winders machines and JP is right on the money. Only difference is price and the signal generators which on Dell's machine is a worked over off-the-shelf signal generator that will run off a battery and the JP device that generates the signal with a simple chip. Anyone with 2 brain cells operating can build the JP shown device including the rotator rods for $30 or less. They both do the same thing - NOTHING WORTHWHILE!
Goldfinder

[Carl-NC]

J PLAYER, you are so full of BS, you couldn't tell the truth if your life depended on it.

Shame on you for posting false information to unsuspecting viewers. Dell

I've seen several of Dell's machines, and while they don't have "the same" circuit as the 8038, they definitely have "the same kind" of circuit. So JP is right.

The shame is adding useless electronics to a pair of dowsing rods and passing it off as anything more than... useless.

[oroboy]

digital

https://www.youtube.com/watch?v=hCzyMQQAfCM

[J_Player]

hi wm6 and j-p and geo and other freinds
I worked with my mfd.Bars indicate one point, according to j-p.

http://www.longrangelocators.com/forums/showpost.php?p=141681&postcount=10

http://www.longrangelocators.com/forums/showpost.php?p=141684&postcount=13

I dug into the specified location and took out a stone at a depth of 120 cm.
my lrl detect Was evident in the stone.
How do I make the distinction between rock and metal veins?
How do I filter would only reveal rocks and minerals and metals?

Hi ma330,
I can think of one reason why you have problems with your MFD dowsing.
If you go to the page that shows the instructions for building and using the MFD, then you can look at the bottom of the page to see the answer:

http://www.geotech1.com/cgi-bin/pages/common/index.pl?page=lrl&file=/projects/mfd1/index.dat

"Once you have the target pinpointed you may have to face another problem: depth. The MFD can detect targets as deep as 100-200 feet, so locating the target is only half the battle. If a metal detector does not verify the existence of a metal target at the identified location then you should bring in excavation equipment. If no obvious target is found when you reach 200 feet, then the target was most likely subatomic gold particles - you cannot see it and most chemical analyses will not detect it either, but the MFD will".

You can see that you have correctly found the treasure.
But there are two problems which you must now solve:
1. The treasure is not the rock you dug, because a rock is not a metal treasure.
We can see you did not dig deep enough.
You will need to dig much deeper to find the real treasure which is buried beneath the rock.
Maybe you will need to dig 200 feet deep before you find the treasure.
So you must go to rent a tractor such as an excavator to dig a very deep hole.
If you are lucky, you might find the treasure in the first two or three days of digging.

2. If you don't find the treasure after a week of digging with a tractor, then maybe the treasure is subatomic gold particles.
If this is what you detected, then you will not find it because these particles of gold are too small to see.
But you can be happy to know that your MFD worked to find it.
This means you did a good job of building your MFD because you were successful in locating the subatomic gold particles.

I hope this solves the mystery of MFD and convinces you that MFD really works.
If you begin to think that MFD does not work, then you are beginning to think the same as most treasure hunters who prefer to leave the MFD at home and use a metal detector.

Best wishes,
J_P

[ma330]

i have a problem
When I put the measuring frequency.Frequency is 5 kHz.When the probe is connected to the ground I change the frequency.Frequency of 5 kHz is transmitted when the connection to the land or a frequency oscillator is also changed?
I set the frequency of re-connecting the probe to the ground?
Or changes due to land Resistance and a normal thing and it should be noted?The frequency is 5 kHz and transferred to the frequency that the frequency counter?

[WM6]

If you think that frequency have to be 5kHz, then it have to be 5kHz, not 4.86 or 5.25.

Mean you need stable frequency generator, without changing frequency after connection to earth.

Probably digitalised version of signal generation.

[ma330]

tank you wm6
Whether a probe containing positive frequencies can also play the same frequency in the ground?
Similar picture

[reza vir]

I need information about a mfd project.And I need a schematic for mfd.Can anyone help me?

The circuit further searches metals
The only problem is, there is no frequency variable capacitors suffering?? Gold and Silver

[mahinda]

my friend.....

please give me answer this dowsing problem .what is connect circuit diagrams dowsing rod ?

[reza vir]

my friend.....

please give me answer this dowsing problem .what is connect circuit diagrams dowsing rod ?

Hello my friend in this type of device MFD.
The bars do not connect
Generators connected to the ground by the probe.

[pigeon]

for kakale

hi all

please anyone have the pcb in format pdf

thank you for help

p.

[UltraLRL]

hi to all
What is the best in class amplifier to boost the frequency to penetrate to the ground(for mfd)?
A?B?...?
please answer
TANK YOU

CLASS A, Because Class-A Output devices conduct through 360 degrees of input cycle.

[UltraLRL]

Another ICL8038 Function Generator



by Andy Collinson

read more at :
http://www.zen22142.zen.co.uk/Circui...ar/funcgen.htm

[goldfinder]

8038 Lousy Sigen

The 8038 like the 555 is basically a resistor capacitor oscillator and they drift in frequency with temperature. If you want frequency stability use a PIC uC with a timer loop which is very stable.
GoldFinder

[reza vir]

The 8038 like the 555 is basically a resistor capacitor oscillator and they drift in frequency with temperature. If you want frequency stability use a PIC uC with a timer loop which is very stable.
GoldFinder

Hello my friend
Do you have a specific circuit?
Send to me Thanks & Regards