Lrl from Italy

[Dubulumach]

As I have already said I do not have much experience in research so I do not know if you can evaluate the depth of the buried metal. The fact that the signal disappears on the vertical of the target is normal. I have never experienced a disturbance of the ground but rather a sky effect, ie the appearance of a signal by lowering or raising the lrl. However this effect is connected to the compass effect and disappear together by lowering the gain. As for the coil stimulator my first functioning lrl in practice it was a PI, a 60Khz pulse oscillator excited a resonant coil at about 5Mhz, the receiving coil, arranged perpendicularly to reduce the signal. The signal of the receiving coil and that of the antenna (V-shaped) were mixed in a toroidal transformer and sent to amplifier and sampler stages. The transmitter coil was the same as the oscillator at 8Mhz in my last lrl but according to me it was not useful for operation, or at least it is more complicated to realize and to fine-tune. We can say that the first exemplar of lrl built by Alonzo was a commercial metal detector modified with the addition of a ferrite coil, which was the receiving antenna. In my opinion, all lrls are of a passive type and no signal is transmitted, there may be some kind of filter to highlight gold but I have doubts about their effectiveness.

Yes i think exactly on that continuous appearance of a signal by lowering to the ground or raising to the sky the lrl stylus-whip antenna as you called it sky effect. Overal lrl gain should be lowered enough, to avoid this unpleasant sky effect. I also have very strong signal with your quartz lrl - (all 3 lrl's led diodes fully lit), something about 40 meter in distance to nearest earthed roman tombs, while in previous prospecting area, several days before over the earthed tombs, magnetometer power supply unit has burnt from the phenomenon force rising from underground.

Thank you very much FrancoITALY on valuable informations.
Seems to me that you are the BEST MAN HERE AT THIS FORUM. GOOD LUCK, BEST WISHES.

Dubulumach

[Dubulumach]

Nice look, isn't it, FrancoItaly ?

We both need lot of these shiny stuffs to make our life days easy.

thank you FrancoItaly for your help and nice references.

Best regards
Dubulumach

[FrancoItaly]

Nice look, isn't it, FrancoItaly ?

We both need lot of these shiny stuffs to make our life days easy.

thank you FrancoItaly for your help and nice references.

Best regards
Dubulumach

It's the dream of all those who have a metal detector or lrl and sometimes dreams come true ...

[Dubulumach]

It's the dream of all those who have a metal detector or lrl and sometimes dreams come true ...

yes FrancoItaly,
everything is a LIE except GOLD, only GOLD is forever.

Much GOLD you have grabbed, much eternity you have. So in this line, the sense of life is THE GOLD.


Best regards
Dubulumach

[Dubulumach]

FrancoItaly

Here is some info for you and lrl builders about Tesla telluric currents or telluric waves or golden waves detector.

Long time ago it had been reported that Nikola Tesla made a device which allowed him to hear sounds at very great distances. I have never seen any Tesla's details about of the circuitry used by Nikola Tesla. But in 1986 year, american Dave Lawton has produced such a device, and he reports that he could hear human conversations taking place 4 1/2 miles away from him or 7,2 km. Interestingly, the sounds from 7,2 km were also travelling through a solid state stone wall some three feet thick cca. 90 cm.. The circuit for this device is described in Radio-Electronics Magazine in April 1986.






The circuit shown here comprising of two 741 operational amplifiers connected as a two-stage amplifier. The unusual feature is very small amount of white noise being injected at the piezo tranducer at input of op. amp. The white noise is generated by the 5 volt zener diode. The level of white noise is controlled by 1.5 Meg variable resistor, plus the 10K fixed resistor. While the range of these two components is 10K to 1.501 Meg. the working setting is normally very high and so only a very small amount of white noise is fed into the input of the first 741 op. amp. to modify the tranducer input. The adjustment of injection of white noise is the main control here, and it has been found experimentally, that when the tuning or pot.setting is correctt, the circuit has the feel the strange telluric echoes from positive op feedback. This device is is operated by turning the gain high up until the op. amp. just reaches self-oscillation, and then backing the gain off very-very slightly. The white noise source is then adjusted until the unit is producing a echoing of the sound. The result is a device which has hear Tesla's telluric waves.

Gregory Hodowanec "All About Gravitational Waves" or using Tesla termonology TELLURIC WAVES OR THE UNDERGROUND WAVES or in my interpretation THE GOLDEN WAVES.

http://www.rexresearch.com/hodorhys/remag86/remag86.htm

ps. now you know about the stuff you have a deal in your passive rf-sniffer. The same Tesla technology 100 years old.

ps1. keep your Francoitaly LRL thread alive.

ps2. wainting with patience yours new infra-red lrl version.

Best regards
Dubulumach

[Dubulumach]

Esteban: "Yes the founds (gold) was with the modified Zahori, you have in the output of the transformer the necessary signal. You must clean very well the PCB after solder."

ps. IMHO 11.3 Hz pulsing should be used instead 100 Hz, or overtones of 11hz.

ps2. "Photonic Aspects of Dowsing and Feng Shui", M.Krinker, A.Goykadosh City College of Technology, Department of Electrical Engineering and Telecommunications, CUNY, New York.

http://rangertell.com/wp-content/uploads/2015/07/72708396-Photonic-Aspects-of-Dowsing-and-Feng-Shui.pdf

see also
ttps://rangertell.com/technical/

Best wishes
Dubulumach

[FrancoItaly]

Esteban: "Yes the founds (gold) was with the modified Zahori, you have in the output of the transformer the necessary signal. You must clean very well the PCB after solder."

ps. IMHO 11.3 Hz pulsing should be used instead 100 Hz, or overtones of 11hz.

ps2. "Photonic Aspects of Dowsing and Feng Shui", M.Krinker, A.Goykadosh City College of Technology, Department of Electrical Engineering and Telecommunications, CUNY, New York.

http://rangertell.com/wp-content/uploads/2015/07/72708396-Photonic-Aspects-of-Dowsing-and-Feng-Shui.pdf

see also
ttps://rangertell.com/technical/

Best wishes
Dubulumach

Very interesting, something I had read in the past, unfortunately at the moment I can do little. An important improvement for my lrl would be to eliminate the compass effect in order to increase the gain.

[abdou2014]

Franco infra-red lrl version

[abdou2014]

https://www.dropbox.com/s/vmn3nccla8mbk8h/2011-01-16%2007.39.54.jpg?dl=0

[Dubulumach]

https://www.dropbox.com/s/vmn3nccla8...39.54.jpg?dl=0

Schematic, info, tuning, tests, vids ?

[Dubulumach]

Very interesting, something I had read in the past, unfortunately at the moment I can do little. An important improvement for my lrl would be to eliminate the compass effect in order to increase the gain.

FrancoItaly I need you help tuning hef4046 LRL-PLL to detect gold. Step by step instructions and improvements for your LRL-PLL to eliminate the compass effect with maximum possible gain without signal distorsion.

I am running currently a lot of experiments, your hef4046 LRL-PLL with special tuning detect my force-field or my aura. Around a healthy and powerful man like me there is 40 cm force-field from my bio-life-force. I am currently not interesting in bio-enginiiering and DNA modifications. Al my interests are about THE GOLD. My display sensor stage 3x LM3915 with 3 bar graphs, meassure tiny signals with 10mV steps with resistive prescaling input signal in some proportion. I was changed both variables, input coil L inductance and variable capacitance C at input of PLL-LRL. Also lenght of stylus-whip antenna is variale inmy case.

Also i was implemented GEO modification, by precise trimming amount of mixing pll oscillator signal from pins 4,6 to the input of 3,3nf capacitor via 20 turns vishay variable resistor 10K. The main trick is in a exactly correct proportion between two signals - from oscillator and what came through the stylus-whip antenna, because the device pick up many non electrical signals with unknown origins.

I need to know correct dc offset after 3rd order LP-filter to adjust 3 x LM3914 to cover entire signal range with minimum meassuring steps.

Would you like to help me TO ADJUST IT ONLY FOR GOLD ?

If youl like post your Infra-red LRL and i will try it in a practice on roman's earthed towns and fortresses.

best wishes
Dubulumach

[Dubulumach]

Single and Dual LM3914 V3.1 Calculator

http://www.electro-tech-online.com/attachments/lm3914h-exe.54277/

http://www.electro-tech-online.com/attachments/duallm3914a-exe.42616/

you need to install the VBR files to run LM3914 calc from here

http://support.microsoft.com/kb/180071/EN-US/

[FrancoItaly]

FrancoItaly I need you help tuning hef4046 LRL-PLL to detect gold. Step by step instructions and improvements for your LRL-PLL to eliminate the compass effect with maximum possible gain without signal distorsion.

I am running currently a lot of experiments, your hef4046 LRL-PLL with special tuning detect my force-field or my aura. Around a healthy and powerful man like me there is 40 cm force-field from my bio-life-force. I am currently not interesting in bio-enginiiering and DNA modifications. Al my interests are about THE GOLD. My display sensor stage 3x LM3915 with 3 bar graphs, meassure tiny signals with 10mV steps with resistive prescaling input signal in some proportion. I was changed both variables, input coil L inductance and variable capacitance C at input of PLL-LRL. Also lenght of stylus-whip antenna is variale inmy case.

Also i was implemented GEO modification, by precise trimming amount of mixing pll oscillator signal from pins 4,6 to the input of 3,3nf capacitor via 20 turns vishay variable resistor 10K. The main trick is in a exactly correct proportion between two signals - from oscillator and what came through the stylus-whip antenna, because the device pick up many non electrical signals with unknown origins.

I need to know correct dc offset after 3rd order LP-filter to adjust 3 x LM3914 to cover entire signal range with minimum meassuring steps.

Would you like to help me TO ADJUST IT ONLY FOR GOLD ?

If youl like post your Infra-red LRL and i will try it in a practice on roman's earthed towns and fortresses.

best wishes
Dubulumach

I do not know how to calibrate my lrl to reveal only gold (I don't know if is possible)), I also have no more place to test with gold.
I did not try my lrl with infrared, I just gave some theoretical advice. to correct dc offset after 3rd order LP-filter you can sum it to a suitable DC voltage via an LM358.
Step by step instructions and improvements for my LRL-PLL are the same that 8Mhz version.

[abdou2014]

IR TX 1500 HZ

[abdou2014]

??